ATV12H018F1 Schneider Electric Industrial Automation Components

Product Details

• Maximum Horse Power Rating
  0.25 hp
• Transmission Frame
  RTU for Modbus
• Product Destination
  Asynchronous motors
• EMC Filter
  Without EMC filter
• Range Of Product
  Altivar 12
• Motor Power Kw
  0.18 kW
• Noise Level
  0 dB
• Maximum Transient Current
  2.1 A 60 s
• Speed Range
  1…20
• Prospective Line Isc
  1 kA
• Discrete Input Type
  Programmable LI1...LI4 24 V 18...30 V
• Assembly Style
  On base plate
• Supply Frequency
  50/60 Hz +/- 5 %
• Speed Drive Output Frequency
  0.5…400 Hz
• Insulation
  Electrical between power and control
• Product Specific Application
  Simple machine
• [Us] Rated Supply Voltage
  100...120 V - 15...10 %
• Built-In Fan
  Without
• Connector Type
  1 RJ45 (on front face) for Modbus
• Braking Torque
  Up to 70 % of nominal motor torque without braking resistor
Analogue Input Number
1
Minimum Switching Current
5 mA 24 V DC logic relay
IP Degree Of Protection
IP20 without blanking plate on upper part
Component Name
ATV12
Phase
1 phase
Quantity Per Set
Set of 1
Transient Overtorque
150…170 % of nominal motor torque depending on drive rating and type of motor
Output Voltage
200...240 V 3 phase
Discrete Input Number
4
Product Or Component Type
Variable speed drive
Communication Port Protocol
Modbus
Number Of Addresses
1…247 Modbus
Continuous Output Current
1.4 A 4 kHz
Marking
CE
Height
5.63 in (143 mm)
Time Constant
20 ms +/- 1 ms for reference change
Physical Interface
2-wire RS 485 for Modbus
Tightening Torque
7.08 lbf.in (0.8 N.m)
Nominal Switching Frequency
4 kHz
Linearity Error
+/- 0.3 % of maximum value analogue input
Braking To Standstill
By DC injection, <30 s
Specific Application
Commercial equipment
Electrical Connection
Terminal 3.5 mm², AWG 12 L1, L2, L3, U, V, W, PA, PC)
Analogue Output Number
1
Width
2.83 in (72 mm)
Motor Starter Type
Variable speed drive
Operating Position
Vertical +/- 10 degree
Discrete Output Number
2
Depth
4.02 in (102.2 mm)
Net Weight
1.54 lb(US) (0.7 kg)
Acceleration And Deceleration Ramps
S U Linear from 0 to 999.9 s
Analogue Output Type
AO1 software-configurable voltage 0...10 V 470 Ohm 8 bits AO1 software-configurable current 0...20 mA 800 Ohm 8 bits
Motor Slip Compensation
Adjustable Preset in factory
Line Current
6 A 100 V 5 A 120 V
Switching Frequency
2...16 kHz adjustable 4...16 kHz with derating factor
Sampling Duration
20 ms +/- 1 ms logic input 10 ms analogue input
Frequency Resolution
Analog input converter A/D, 10 bits Display unit 0.1 Hz
Discrete Input Logic
Negative logic (sink), > 16 V, < 10 V 3.5 kOhm Positive logic (source), 0...< 5 V, > 11 V
Supply
Internal supply for reference potentiometer 5 V DC 4.75…5.25 V), <10 mA overload and short-circuit protection Internal supply for logic inputs 24 V DC 20.4…28.8 V), <100 mA overload and short-circuit protection
Discrete Output Type
Logic output LO+, LO- Protected relay output R1A, R1B, R1C 1 C/O
Asynchronous Motor Control Profile
Quadratic voltage/frequency ratio Voltage/frequency ratio (V/f) Sensorless flux vector control
Variable Speed Drive Application Selection
Mixer Commercial equipment Other application Commercial equipment Ironing Textile
Analogue Input Type
Configurable current AI1 0...20 mA 250 Ohm Configurable voltage AI1 0...10 V 30 kOhm Configurable voltage AI1 0...5 V 30 kOhm
Transmission Rate
4800 bit/s 9600 bit/s 19200 bit/s 38400 bit/s
Maximum Switching Current
2 A 250 V AC inductive cos phi = 0.4 L/R = 7 ms logic relay 2 A 30 V DC inductive cos phi = 0.4 L/R = 7 ms logic relay 3 A 250 V AC resistive cos phi = 1 L/R = 0 ms logic relay 4 A 30 V DC resistive cos phi = 1 L/R = 0 ms logic relay
Communication Service
Read holding registers (03) 29 words Write single register (06) 29 words Write multiple registers (16) 27 words Read/write multiple registers (23) 4/4 words Read device identification (43)
Protection Type
Line supply overvoltage Line supply undervoltage Overcurrent between output phases and earth Overheating protection Short-circuit between motor phases Against input phase loss in three-phase Thermal motor protection via the d

ATV12H018F1 Related Documents