ATV12HU15M2 Schneider Electric Industrial Automation Components

Product Details

• Component Name
  ATV12
• Noise Level
  45 dB
• Motor Power Kw
  1.5 kW
• EMC Filter
  Integrated
• Product Specific Application
  Simple machine
• Communication Port Protocol
  Modbus
• Connector Type
  1 RJ45 (on front face) for Modbus
• [Us] Rated Supply Voltage
  200...240 V - 15...10 %
• Nominal Switching Frequency
  4 kHz
• Product Or Component Type
  Variable speed drive
• Range Of Product
  Altivar 12
• Quantity Per Set
  Set of 1
• Speed Range
  1…20
• Supply Frequency
  50/60 Hz +/- 5 %
• Continuous Output Current
  7.5 A 4 kHz
• Discrete Input Number
  4
• Specific Application
  Commercial equipment
• Braking To Standstill
  By DC injection, <30 s
• Motor Starter Type
  Variable speed drive
• Functionality
  Basic
Number Of Addresses
1…247 Modbus
Output Voltage
200...240 V 3 phase
Operating Position
Vertical +/- 10 degree
Width
4.13 in (105 mm)
Depth
6.15 in (156.2 mm)
Assembly Style
With heat sink
Physical Interface
2-wire RS 485 for Modbus
Discrete Input Type
Programmable LI1...LI4 24 V 18...30 V
Minimum Switching Current
5 mA 24 V DC logic relay
Marking
CE
Net Weight
3.09 lb(US) (1.4 kg)
IP Degree Of Protection
IP20 without blanking plate on upper part
Prospective Line Isc
1 kA
Tightening Torque
10.62 lbf.in (1.2 N.m)
Linearity Error
+/- 0.3 % of maximum value analogue input
Analogue Input Number
1
Built-In Fan
With
Electrical Connection
Terminal 5.5 mm², AWG 10 L1, L2, L3, U, V, W, PA, PC)
Transmission Frame
RTU for Modbus
Braking Torque
Up to 70 % of nominal motor torque without braking resistor
Analogue Output Number
1
Insulation
Electrical between power and control
Discrete Output Number
2
Height
5.59 in (142 mm)
Phase
1 phase
Maximum Transient Current
11.2 A 60 s
Transient Overtorque
150…170 % of nominal motor torque depending on drive rating and type of motor
Speed Drive Output Frequency
0.5…400 Hz
Product Destination
Asynchronous motors
Maximum Horse Power Rating
2 hp
Time Constant
20 ms +/- 1 ms for reference change
Discrete Output Type
Logic output LO+, LO- Protected relay output R1A, R1B, R1C 1 C/O
Switching Frequency
2...16 kHz adjustable 4...16 kHz with derating factor
Motor Slip Compensation
Adjustable Preset in factory
Sampling Duration
20 ms +/- 1 ms logic input 10 ms analogue input
Discrete Input Logic
Negative logic (sink), > 16 V, < 10 V 3.5 kOhm Positive logic (source), 0...< 5 V, > 11 V
Analogue Output Type
AO1 software-configurable voltage 0...10 V 470 Ohm 8 bits AO1 software-configurable current 0...20 mA 800 Ohm 8 bits
Line Current
17.8 A 200 V 14.9 A 240 V
Supply
Internal supply for reference potentiometer 5 V DC 4.75…5.25 V), <10 mA overload and short-circuit protection Internal supply for logic inputs 24 V DC 20.4…28.8 V), <100 mA overload and short-circuit protection
Frequency Resolution
Analog input converter A/D, 10 bits Display unit 0.1 Hz
Analogue Input Type
Configurable current AI1 0...20 mA 250 Ohm Configurable voltage AI1 0...10 V 30 kOhm Configurable voltage AI1 0...5 V 30 kOhm
Acceleration And Deceleration Ramps
U S Linear from 0 to 999.9 s
Maximum Switching Current
2 A 250 V AC inductive cos phi = 0.4 L/R = 7 ms logic relay 2 A 30 V DC inductive cos phi = 0.4 L/R = 7 ms logic relay 3 A 250 V AC resistive cos phi = 1 L/R = 0 ms logic relay 4 A 30 V DC resistive cos phi = 1 L/R = 0 ms logic relay
Variable Speed Drive Application Selection
Mixer Commercial equipment Other application Commercial equipment Ironing Textile
Asynchronous Motor Control Profile
Sensorless flux vector control Quadratic voltage/frequency ratio Voltage/frequency ratio (V/f)
Transmission Rate
4800 bit/s 9600 bit/s 19200 bit/s 38400 bit/s
Communication Service
Read holding registers (03) 29 words Write single register (06) 29 words Write multiple registers (16) 27 words Read/write multiple registers (23) 4/4 words Read device identification (43)
Protection Type
Line supply overvoltage Line supply undervoltage Overcurrent between output phases and earth Overheating protection Short-circuit between motor phases Against input phase loss in three-phase Thermal motor protection via the d