ATV12HU30M3 Schneider Electric Industrial Automation Components

Product Details

• EMC Filter
  Without EMC filter
• Phase
  3 phase
• Operating Position
  Vertical +/- 10 degree
• Supply Frequency
  50/60 Hz +/- 5 %
• Prospective Line Isc
  5 kA
• Output Voltage
  200...240 V 3 phase
• Discrete Input Type
  Programmable LI1...LI4 24 V 18...30 V
• Product Specific Application
  Simple machine
• Maximum Horse Power Rating
  4 hp
• IP Degree Of Protection
  IP20 without blanking plate on upper part
• Continuous Output Current
  12.2 A 4 kHz
• Communication Port Protocol
  Modbus
• Tightening Torque
  10.62 lbf.in (1.2 N.m)
• Discrete Output Number
  2
• Quantity Per Set
  Set of 1
• Analogue Input Number
  1
• Linearity Error
  +/- 0.3 % of maximum value analogue input
• Time Constant
  20 ms +/- 1 ms for reference change
• Product Destination
  Asynchronous motors
• Speed Range
  1…20
Number Of Addresses
1…247 Modbus
Maximum Transient Current
18.3 A 60 s
Range Of Product
Altivar 12
Built-In Fan
With
Transient Overtorque
150…170 % of nominal motor torque depending on drive rating and type of motor
Transmission Frame
RTU for Modbus
Speed Drive Output Frequency
0.5…400 Hz
Analogue Output Number
1
Braking To Standstill
By DC injection, <30 s
Height
7.24 in (184 mm)
Marking
CE
Depth
5.56 in (141.2 mm)
Component Name
ATV12
[Us] Rated Supply Voltage
200...240 V - 15...10 %
Noise Level
50 dB
Discrete Input Number
4
Minimum Switching Current
5 mA 24 V DC logic relay
Assembly Style
With heat sink
Connector Type
1 RJ45 (on front face) for Modbus
Nominal Switching Frequency
4 kHz
Electrical Connection
Terminal 5.5 mm², AWG 10 L1, L2, L3, U, V, W, PA, PC)
Width
5.51 in (140 mm)
Motor Power Kw
3 kW
Physical Interface
2-wire RS 485 for Modbus
Braking Torque
Up to 70 % of nominal motor torque without braking resistor
Insulation
Electrical between power and control
Product Or Component Type
Variable speed drive
Net Weight
4.41 lb(US) (2 kg)
Motor Starter Type
Variable speed drive
Specific Application
Commercial equipment
Discrete Output Type
Logic output LO+, LO- Protected relay output R1A, R1B, R1C 1 C/O
Line Current
19 A 200 V 15.9 A 240 V
Frequency Resolution
Analog input converter A/D, 10 bits Display unit 0.1 Hz
Discrete Input Logic
Negative logic (sink), > 16 V, < 10 V 3.5 kOhm Positive logic (source), 0...< 5 V, > 11 V
Sampling Duration
20 ms +/- 1 ms logic input 10 ms analogue input
Supply
Internal supply for reference potentiometer 5 V DC 4.75…5.25 V), <10 mA overload and short-circuit protection Internal supply for logic inputs 24 V DC 20.4…28.8 V), <100 mA overload and short-circuit protection
Motor Slip Compensation
Adjustable Preset in factory
Switching Frequency
2...16 kHz adjustable 4...16 kHz with derating factor
Analogue Output Type
AO1 software-configurable voltage 0...10 V 470 Ohm 8 bits AO1 software-configurable current 0...20 mA 800 Ohm 8 bits
Asynchronous Motor Control Profile
Sensorless flux vector control Quadratic voltage/frequency ratio Voltage/frequency ratio (V/f)
Acceleration And Deceleration Ramps
Linear from 0 to 999.9 s S U
Analogue Input Type
Configurable current AI1 0...20 mA 250 Ohm Configurable voltage AI1 0...10 V 30 kOhm Configurable voltage AI1 0...5 V 30 kOhm
Variable Speed Drive Application Selection
Mixer Commercial equipment Other application Commercial equipment Ironing Textile
Transmission Rate
4800 bit/s 9600 bit/s 19200 bit/s 38400 bit/s
Maximum Switching Current
2 A 250 V AC inductive cos phi = 0.4 L/R = 7 ms logic relay 2 A 30 V DC inductive cos phi = 0.4 L/R = 7 ms logic relay 3 A 250 V AC resistive cos phi = 1 L/R = 0 ms logic relay 4 A 30 V DC resistive cos phi = 1 L/R = 0 ms logic relay
Communication Service
Read holding registers (03) 29 words Write single register (06) 29 words Write multiple registers (16) 27 words Read/write multiple registers (23) 4/4 words Read device identification (43)
Protection Type
Line supply overvoltage Line supply undervoltage Overcurrent between output phases and earth Overheating protection Short-circuit between motor phases Against input phase loss in three-phase Thermal motor protection via the d

ATV12HU30M3 Related Documents