ATV212HD15N4 Schneider Electric Industrial Automation Components

Product Details

• Regulation Loop
  Adjustable PI regulator
• Insulation Resistance
  >= 1 mOhm 500 V DC for 1 minute
• Maximum Horse Power Rating
  20 hp
• Maximum Transient Current
  33.6 A 60 s
• Product Specific Application
  Pumps and fans in HVAC
• Supply Frequency
  50...60 Hz - 5...5 %
• Torque Accuracy
  +/- 15 %
• Power Dissipation In W
  625 W
• Phase
  3 phase
• Supply Voltage Limits
  323…528 V
• Transient Overtorque
  120 % of nominal motor torque +/- 10 % 60 s
• Local Signalling
  for DC bus energized 1 LED (red)
• Analogue Output Number
  1
• Motor Power Kw
  15 kW
• Apparent Power
  23.2 kVA 380 V
• Speed Range
  1…10
• Range Of Product
  Altivar 212
• Product Destination
  Asynchronous motors
• Prospective Line Isc
  22 kA
• Speed Accuracy
  +/- 10 % of nominal slip 0.2 Tn to Tn
Assembly Style
With heat sink
Speed Drive Output Frequency
0.5…200 Hz
Nominal Switching Frequency
12 kHz
Analogue Input Number
2
Discrete Output Number
2
Physical Interface
2-wire RS 485
Width
9.65 in (245 mm)
Option Card
Communication card LonWorks
Product Or Component Type
Variable speed drive
[Us] Rated Supply Voltage
380...480 V - 15...10 %
Transmission Frame
RTU
Height
12.99 in (330 mm)
Motor Starter Type
Variable speed drive
Device Short Name
ATV212
EMC Filter
Class C2 EMC filter integrated
Output Voltage
<= power supply voltage
Braking To Standstill
By DC injection
Air Flow
54420.42 Gal/hr(US) (206 m3/h)
Number Of Addresses
1…247
IP Degree Of Protection
IP21
Data Format
8 bits, 1 stop, odd even or no configurable parity
Functionality
Mid
Minimum Switching Current
3 mA 24 V DC configurable relay logic
Transmission Rate
9600 bps or 19200 bps
Depth
7.48 in (190 mm)
Net Weight
25.68 lb(US) (11.65 kg)
Isolation
Electrical between power and control
Type Of Polarization
No impedance
Specific Application
HVAC
Operating Position
Vertical +/- 10 degree
Discrete Input Logic
Positive logic (source) F, R, RES), <= 5 V, >= 11 V Negative logic (sink) F, R, RES), >= 16 V, <= 10 V
Line Current
22.8 A 480 V 28.5 A 380 V
Tightening Torque
5.31 lbf.in (0.6 N.m) VIA, VIB, FM, FLA, FLB, FLC, RY, RC, F, R, RES) 39.83 lbf.in (4.5 N.m), 40 lb.in L1/R, L2/S, L3/T)
Switching Frequency
6...16 kHz adjustable 12...16 kHz with derating factor
Electrical Connection
VIA, VIB, FM, FLA, FLB, FLC, RY, RC, F, R, RES terminal 0.00 in² (2.5 mm²) / AWG 14 L1/R, L2/S, L3/T terminal 0.04 in² (25 mm²) / AWG 3
Continuous Output Current
30.5 A 380 V 30.5 A 460 V
Motor Power Range AC-3
15…25 kW 380…440 V 3 phase 15…25 kW 480…500 V 3 phase
Supply
Internal supply for reference potentiometer (1 to 10 kOhm) 10.5 V DC +/- 5 %, <10 A overload and short-circuit protection Internal supply 24 V DC 21…27 V), <200 A overload and short-circuit protection
Frequency Resolution
Display unit 0.1 Hz Analog input: 0.024/50 Hz
Analogue Output Type
FM switch-configurable voltage 0...10 V DC 7620 Ohm 10 bits FM switch-configurable current 0...20 mA 970 Ohm 10 bits
Dielectric Strength
3535 V DC between earth and power terminals 5092 V DC between control and power terminals
Connector Type
1 open style 1 RJ45
Acceleration And Deceleration Ramps
Linear adjustable separately from 0.01 to 3200 s Automatic based on the load
Motor Slip Compensation
Automatic whatever the load Not available in voltage/frequency ratio motor control Adjustable
Linearity Error
VIA +/- 0.15 % of maximum value input VIB +/- 0.15 % of maximum value input FM +/- 0.2 % output
Discrete Input Type
F programmable 24 V DC level 1 PLC 4700 Ohm R programmable 24 V DC level 1 PLC 4700 Ohm RES programmable 24 V DC level 1 PLC 4700 Ohm
Discrete Output Type
Configurable relay logic FLA, FLC) NO - 100000 cycles Configurable relay logic FLB, FLC) NC - 100000 cycles Configurable relay logic RY, RC) NO - 100000 cycles
Type Of Cable
Without mounting kit 1 IEC cable 113 °F (45 °C), copper 90 °C / XLPE/EPR Without mounting kit 1 IEC cable 113 °F (45 °C), copper 70 °C / PVC With UL Type 1 kit 3 UL 508 cable 104 °F (40 °C), copper 75 °C / PVC
Accuracy
+/- 0.6 % VIA) for a temperature variation 60 °C +/- 0.6 % VIB) for a temperature variation 60 °C +/- 1 % FM) for a temperature variation 60 °C
Variable Speed Drive Application Selection
Compressor for scroll Building - HVAC Fan Building - HVAC Pump Building - HVAC
Response Time
FM 2 ms +/- 0.5 ms analog FLA, FLC 7 ms +/- 0.5 ms discrete FLB, FLC 7 ms +/- 0.5 ms discrete RY, RC 7 ms +/- 0.5 ms discrete
Analogue Input Type
VIA switch-configurable voltage 0...10 V DC 24 V max 30000 Ohm 10 bits VIB configurable voltage 0...10 V DC 24 V max 30000 Ohm 10 bits VIB configurable PTC probe 0...6 probes 1500 Ohm VIA switch-configurable current 0...20 mA 250 Ohm 10 bit
Maximum Switching Current
5 A 250 V AC resistive cos phi = 1 L/R = 0 ms FL, R) 5 A 30 V DC resistive cos phi = 1 L/R = 0 ms FL, R) 2 A 250 V AC inductive cos phi = 0.4 L/R = 7 ms FL, R) 2 A 30 V DC inductive cos phi = 0.4 L/R = 7 ms FL, R)
Asynchronous Motor Control Profile
Flux vector control without sensor, standard Voltage/frequency ratio, 2 points Voltage/frequency ratio, automatic IR compensation (U/f + automatic Uo) Voltage/frequency ratio - Energy Saving, quadratic U/f Voltage/frequency ratio, 5 po
Sampling Duration
2 ms +/- 0.5 ms F discrete 2 ms +/- 0.5 ms R discrete 2 ms +/- 0.5 ms RES discrete 3.5 ms +/- 0.5 ms VIA analog 22 ms +/- 0.5 ms VIB analog
Communication Port Protocol
BACnet Modbus METASYS N2 APOGEE FLN LonWorks
Communication Service
Time out setting from 0.1 to 100 s Read device identification (43) Monitoring inhibitable Write single register (06) Write multiple registers (16) 2 words maximum Read holding registers (03) 2 words maximum
Protection Type
Overheating protection drive Thermal power stage drive Short-circuit between motor phases drive Input phase breaks drive Overcurrent between output phases and earth drive Overvoltages on the DC bus drive Break on the control

ATV212HD15N4 Related Documents