ATV12H018M2 Schneider Electric Industrial Automation Components

Product Details

• Product Or Component Type
  Variable speed drive
• IP Degree Of Protection
  IP20 without blanking plate on upper part
• Maximum Transient Current
  2.1 A 60 s
• Linearity Error
  +/- 0.3 % of maximum value analogue input
• Built-In Fan
  Without
• Nominal Switching Frequency
  4 kHz
• Quantity Per Set
  Set of 1
• Speed Range
  1…20
• Tightening Torque
  7.08 lbf.in (0.8 N.m)
• Minimum Switching Current
  5 mA 24 V DC logic relay
• Component Name
  ATV12
• Transient Overtorque
  150…170 % of nominal motor torque depending on drive rating and type of motor
• Speed Drive Output Frequency
  0.5…400 Hz
• Output Voltage
  200...240 V 3 phase
• Analogue Output Number
  1
• Marking
  CE
• Range Of Product
  Altivar 12
• Communication Port Protocol
  Modbus
• Supply Frequency
  50/60 Hz +/- 5 %
• EMC Filter
  Integrated
Number Of Addresses
1…247 Modbus
Insulation
Electrical between power and control
Time Constant
20 ms +/- 1 ms for reference change
Product Specific Application
Simple machine
Motor Power Kw
0.18 kW
Physical Interface
2-wire RS 485 for Modbus
Braking Torque
Up to 70 % of nominal motor torque without braking resistor
Connector Type
1 RJ45 (on front face) for Modbus
Prospective Line Isc
1 kA
Analogue Input Number
1
Product Destination
Asynchronous motors
Maximum Horse Power Rating
0.25 hp
[Us] Rated Supply Voltage
200...240 V - 15...10 %
Continuous Output Current
1.4 A 4 kHz
Transmission Frame
RTU for Modbus
Discrete Input Number
4
Discrete Output Number
2
Net Weight
1.54 lb(US) (0.7 kg)
Operating Position
Vertical +/- 10 degree
Specific Application
Commercial equipment
Electrical Connection
Terminal 3.5 mm², AWG 12 L1, L2, L3, U, V, W, PA, PC)
Motor Starter Type
Variable speed drive
Noise Level
0 dB
Height
5.63 in (143 mm)
Braking To Standstill
By DC injection, <30 s
Functionality
Basic
Discrete Input Type
Programmable LI1...LI4 24 V 18...30 V
Width
2.83 in (72 mm)
Assembly Style
On base plate
Phase
1 phase
Depth
4.02 in (102.2 mm)
Analogue Output Type
AO1 software-configurable voltage 0...10 V 470 Ohm 8 bits AO1 software-configurable current 0...20 mA 800 Ohm 8 bits
Frequency Resolution
Analog input converter A/D, 10 bits Display unit 0.1 Hz
Supply
Internal supply for reference potentiometer 5 V DC 4.75…5.25 V), <10 mA overload and short-circuit protection Internal supply for logic inputs 24 V DC 20.4…28.8 V), <100 mA overload and short-circuit protection
Motor Slip Compensation
Preset in factory Adjustable
Line Current
3.4 A 200 V 2.8 A 240 V
Discrete Output Type
Logic output LO+, LO- Protected relay output R1A, R1B, R1C 1 C/O
Discrete Input Logic
Negative logic (sink), > 16 V, < 10 V 3.5 kOhm Positive logic (source), 0...< 5 V, > 11 V
Sampling Duration
20 ms +/- 1 ms logic input 10 ms analogue input
Switching Frequency
2...16 kHz adjustable 4...16 kHz with derating factor
Variable Speed Drive Application Selection
Mixer Commercial equipment Other application Commercial equipment Ironing Textile
Asynchronous Motor Control Profile
Voltage/frequency ratio (V/f) Sensorless flux vector control Quadratic voltage/frequency ratio
Analogue Input Type
Configurable current AI1 0...20 mA 250 Ohm Configurable voltage AI1 0...10 V 30 kOhm Configurable voltage AI1 0...5 V 30 kOhm
Acceleration And Deceleration Ramps
U Linear from 0 to 999.9 s S
Maximum Switching Current
2 A 250 V AC inductive cos phi = 0.4 L/R = 7 ms logic relay 2 A 30 V DC inductive cos phi = 0.4 L/R = 7 ms logic relay 3 A 250 V AC resistive cos phi = 1 L/R = 0 ms logic relay 4 A 30 V DC resistive cos phi = 1 L/R = 0 ms logic relay
Transmission Rate
4800 bit/s 9600 bit/s 19200 bit/s 38400 bit/s
Communication Service
Read holding registers (03) 29 words Write single register (06) 29 words Write multiple registers (16) 27 words Read/write multiple registers (23) 4/4 words Read device identification (43)
Protection Type
Line supply overvoltage Line supply undervoltage Overcurrent between output phases and earth Overheating protection Short-circuit between motor phases Against input phase loss in three-phase Thermal motor protection via the d