ATV212HD75N4 Schneider Electric Industrial Automation Components

Product Details

• Maximum Horse Power Rating
  100 hp
• Maximum Transient Current
  176 A 60 s
• Transient Overtorque
  120 % of nominal motor torque +/- 10 % 60 s
• Analogue Input Number
  2
• Analogue Output Number
  1
• Transmission Rate
  9600 bps or 19200 bps
• Specific Application
  HVAC
• Range Of Product
  Altivar 212
• Device Short Name
  ATV212
• Motor Power Kw
  75 kW
• Product Or Component Type
  Variable speed drive
• [Us] Rated Supply Voltage
  380...480 V - 15...10 %
• Nominal Switching Frequency
  8 kHz
• Physical Interface
  2-wire RS 485
• Functionality
  Mid
• EMC Filter
  Class C2 EMC filter integrated
• Speed Range
  1…10
• Output Voltage
  <= power supply voltage
• Insulation Resistance
  >= 1 mOhm 500 V DC for 1 minute
• Local Signalling
  for DC bus energized 1 LED (red)
Discrete Output Number
2
Operating Position
Vertical +/- 10 degree
Depth
11.42 in (290 mm)
Isolation
Electrical between power and control
Data Format
8 bits, 1 stop, odd even or no configurable parity
Width
12.60 in (320 mm)
Motor Starter Type
Variable speed drive
Supply Voltage Limits
323…528 V
Speed Accuracy
+/- 10 % of nominal slip 0.2 Tn to Tn
Speed Drive Output Frequency
0.5…200 Hz
Torque Accuracy
+/- 15 %
Type Of Polarization
No impedance
Air Flow
175941.74 Gal/hr(US) (666 m3/h)
Apparent Power
105.3 kVA 380 V
Minimum Switching Current
3 mA 24 V DC configurable relay logic
Transmission Frame
RTU
Height
24.80 in (630 mm)
Prospective Line Isc
22 kA
Regulation Loop
Adjustable PI regulator
IP Degree Of Protection
IP21
Product Specific Application
Pumps and fans in HVAC
Option Card
Communication card LonWorks
Assembly Style
With heat sink
Number Of Addresses
1…247
Power Dissipation In W
1945 W
Supply Frequency
50...60 Hz - 5...5 %
Product Destination
Asynchronous motors
Phase
3 phase
Braking To Standstill
By DC injection
Discrete Input Logic
Positive logic (source) F, R, RES), <= 5 V, >= 11 V Negative logic (sink) F, R, RES), >= 16 V, <= 10 V
Line Current
141.8 A 380 V 111.3 A 480 V
Continuous Output Current
160 A 380 V 160 A 460 V
Electrical Connection
VIA, VIB, FM, FLA, FLB, FLC, RY, RC, F, R, RES terminal 0.00 in² (2.5 mm²) / AWG 14 L1/R, L2/S, L3/T terminal 0.23 in² (150 mm²) 300 kcmil)
Frequency Resolution
Display unit 0.1 Hz Analog input: 0.024/50 Hz
Acceleration And Deceleration Ramps
Automatic based on the load Linear adjustable separately from 0.01 to 3200 s
Analogue Output Type
FM switch-configurable voltage 0...10 V DC 7620 Ohm 10 bits FM switch-configurable current 0...20 mA 970 Ohm 10 bits
Tightening Torque
5.31 lbf.in (0.6 N.m) VIA, VIB, FM, FLA, FLB, FLC, RY, RC, F, R, RES) 362.88 lbf.in (41 N.m), 360 lb.in L1/R, L2/S, L3/T)
Switching Frequency
6...16 kHz adjustable 8...16 kHz with derating factor
Type Of Cable
Without mounting kit 1 IEC cable 113 °F (45 °C), copper 90 °C / XLPE/EPR Without mounting kit 1 IEC cable 113 °F (45 °C), copper 70 °C / PVC With UL Type 1 kit 3 UL 508 cable 104 °F (40 °C), copper 75 °C / PVC
Connector Type
1 open style 1 RJ45
Dielectric Strength
3535 V DC between earth and power terminals 5092 V DC between control and power terminals
Supply
Internal supply for reference potentiometer (1 to 10 kOhm) 10.5 V DC +/- 5 %, <10 A overload and short-circuit protection Internal supply 24 V DC 21…27 V), <200 A overload and short-circuit protection
Motor Power Range AC-3
55…100 kW 380…440 V 3 phase 55…100 kW 480…500 V 3 phase
Linearity Error
VIA +/- 0.15 % of maximum value input VIB +/- 0.15 % of maximum value input FM +/- 0.2 % output
Discrete Output Type
Configurable relay logic FLA, FLC) NO - 100000 cycles Configurable relay logic FLB, FLC) NC - 100000 cycles Configurable relay logic RY, RC) NO - 100000 cycles
Motor Slip Compensation
Not available in voltage/frequency ratio motor control Automatic whatever the load Adjustable
Accuracy
+/- 0.6 % VIA) for a temperature variation 60 °C +/- 0.6 % VIB) for a temperature variation 60 °C +/- 1 % FM) for a temperature variation 60 °C
Variable Speed Drive Application Selection
Compressor for scroll Building - HVAC Fan Building - HVAC Pump Building - HVAC
Discrete Input Type
F programmable 24 V DC level 1 PLC 4700 Ohm R programmable 24 V DC level 1 PLC 4700 Ohm RES programmable 24 V DC level 1 PLC 4700 Ohm
Maximum Switching Current
5 A 250 V AC resistive cos phi = 1 L/R = 0 ms FL, R) 5 A 30 V DC resistive cos phi = 1 L/R = 0 ms FL, R) 2 A 250 V AC inductive cos phi = 0.4 L/R = 7 ms FL, R) 2 A 30 V DC inductive cos phi = 0.4 L/R = 7 ms FL, R)
Response Time
FM 2 ms +/- 0.5 ms analog FLA, FLC 7 ms +/- 0.5 ms discrete FLB, FLC 7 ms +/- 0.5 ms discrete RY, RC 7 ms +/- 0.5 ms discrete
Analogue Input Type
VIA switch-configurable voltage 0...10 V DC 24 V max 30000 Ohm 10 bits VIB configurable voltage 0...10 V DC 24 V max 30000 Ohm 10 bits VIB configurable PTC probe 0...6 probes 1500 Ohm VIA switch-configurable current 0...20 mA 250 Ohm 10 bit
Sampling Duration
2 ms +/- 0.5 ms F discrete 2 ms +/- 0.5 ms R discrete 2 ms +/- 0.5 ms RES discrete 3.5 ms +/- 0.5 ms VIA analog 22 ms +/- 0.5 ms VIB analog
Asynchronous Motor Control Profile
Voltage/frequency ratio, 5 points Voltage/frequency ratio - Energy Saving, quadratic U/f Voltage/frequency ratio, automatic IR compensation (U/f + automatic Uo) Voltage/frequency ratio, 2 points Flux vector control without sensor, stan
Communication Port Protocol
METASYS N2 Modbus APOGEE FLN BACnet LonWorks
Communication Service
Read device identification (43) Write single register (06) Time out setting from 0.1 to 100 s Monitoring inhibitable Read holding registers (03) 2 words maximum Write multiple registers (16) 2 words maximum
Protection Type
Overheating protection drive Thermal power stage drive Short-circuit between motor phases drive Input phase breaks drive Overcurrent between output phases and earth drive Overvoltages on the DC bus drive Break on the control

ATV212HD75N4 Related Documents