80VD100PD.C000-01 B&R Electronic Components

Product Details

• Weight
  750 g
• B&R ID code
  0xADF7
• Voltage measurement
  Yes
• DC bus capacitance
  940 µF
• Response threshold for open circuit monitoring
  <100 mA
• Degree of protection per EN 60529
  IP20
• Electrical isolation CPU - Power supply
  Yes
• Electrical isolation CPU - EnDat 2.2 interface
  No
• Can be used for Axis 1
  Yes
• Synchronous serial interface Signal transmission
  RS485
• Electrical isolation Input - ACOPOS
  Yes, 500 Veff
• Relative humidity Storage
  5 to 95%, non-condensing
• Voltage monitoring
  Yes
• Quantity
  2
• Max. encoder cable length
  25 m
• Nominal voltage
  24 VDC
• Certifications CE
  Yes
• Can be used for Axis 2
  No
• Switching frequency Inductive load
  See section "Switching inductive loads"
• POWERLINK Electrical isolation
  Yes
Mounting orientation Horizontal
No
Encoder power supply Protective measures Overload-proof
Yes
Overvoltage cutoff
>95 VDC
Possible switching frequencies
5 / 10 / 20 / 40 kHz
Input circuit
Sink
Electrical isolation CPU - 24 VDC power supply
No
Power consumption CPU
Max. 8 W
Power dissipation depending on switching frequency Switching frequency 20 kHz
[0.24×IM1² + 0.214×IM1 + 1.6] W + [0.24×IM2² + 0.214×IM2 + 1.6] W
POWERLINK Variant
Female RJ45 connector
Switching delay Rising edge
[Instant recording] Typ. 52 µs
Relative humidity Transport
5 to 95%, non-condensing
Undervoltage cutoff
<18 VDC
Nominal switching frequency
5 kHz
Modulation compared to ground potential
Max. ±38 V
Backplane
Always mount on conductive and earthed backplane.
Electrical isolation CPU - Digital inputs
Yes
Certifications UL
cULus E225616; Power conversion equipment
Power consumption Continuous power consumption
1.31 kW
Encoder power supply Load capacity
Max. 250 mA
Temperature Storage
-25 to 55°C
Dimensions Depth
95 mm
Input voltage
24 VDC ±25%
Max. current/motor
10.6 ARMS / 15 APeak
Controller frequency
20 kHz
Input current at nominal voltage
Typ. 60 mA
Additional functions
Can be used as trigger input
Electrical isolation CPU - Motor connection
Yes
Certifications KC
Yes
Power dissipation depending on switching frequency Switching frequency 10 kHz
[0.24×IM1² + 0.215×IM1 + 0.8] W + [0.24×IM2² + 0.215×IM2 + 0.8] W
Encoder power supply Output voltage
Typ. 12.5 VDC
Temperature Operation
0 to 45°C
Encoder power supply Protective measures Short-circuit proof
Yes
Line protection
Must occur externally
Type
EnDat 2.2
Max. internal resistance
0.3 Ω
Note
Order terminal blocks and cables separately!
Diagnostics Motor status
Yes, using LED status indicator and software
Power consumption Idle (no motor powered)
0.5 W
Protective measures Overload and short-circuit protection
Yes
Synchronous serial interface Data transfer rate
6.25 Mbit/s
Electrical isolation Input - Input
Yes, 500 Veff
Dimensions Height
134 mm
Inrush current limiting
Yes, PTC (min. 9 Ω), is bypassed during operation by means of relay contact.
Nominal current
Up to 20 kHz: 8 ARMS / 11.3 APeak; At 40 kHz and greater than 45°C: 6.5 ARMS / 9.2 APeak;
Continuous current
1 A
Pollution degree per EN 61800-5-1
2 (non-conductive pollution)
Diagnostics Module temperature / Cooling unit temperature
Yes, using software
Electrical isolation CPU - POWERLINK
Yes
Power dissipation depending on switching frequency Switching frequency 40 kHz
[0.24×IM1² + 0.213×IM1 +3.2] W + [0.24×IM2² + 0.213×IM2 +3.2] W
Input voltage Nominal
24 VDC
Mounting orientation Vertical
Yes
Switching delay at nominal input voltage Enable 1 → 0, PWM off Maximum
500 ms (Rev. < G0: 551 ms)
Inverter module
Connection for two servo motors with EnDat 2.2 encoder
Max. motor cable length
25 m
Input capacitance
10 nF (Rev. < G0: 100 µF)
Diagnostics POWERLINK
Yes, using LED status indicator
Certifications Functional safety
Yes
Switching frequency Resistive load
100 Hz
Protective measures Undervoltage monitoring
Yes
Input voltage Maximum
30 VDC
Temperature Transport
-25 to 55°C
Status indicators
POWERLINK, operating state, module status, motor information
Max. current/module
30 APeak
Isolation voltage between input and bus
500 Veff
Mounting/Cooling
Screw mounting with heat spreader on mounting plate or cold-plate.
Electrical isolation CPU - Enable inputs
Yes
Certifications EAC
Yes
Protective measures Open circuit monitoring
Yes
Switching threshold High
>15 VDC
Relative humidity Operation
5 to 85%, non-condensing
Switching delay at nominal input voltage Enable 0 → 1, ready for PWM Maximum
500 ms
Inrush current
Max. 10 A
Reverse polarity protection
Yes
Response threshold for undervoltage monitoring
≤23.5 V
Input resistance
Approx. 3.2 kΩ
Diagnostics Module run/error
Yes, using LED status indicator and software
Electrical isolation CPU - Trigger inputs
Yes
Electrical isolation CPU - Motor holding brake
No
Power dissipation depending on switching frequency Switching frequency 5 kHz
[0.24×IM1² + 0.216×IM1 + 0.4] W + [0.24×IM2² + 0.216×IM2 + 0.4] W
Switching threshold Low
<5 VDC
Switching delay Falling edge
[Instant recording] Typ. 53 µs
Dimensions Width
65 mm

80VD100PD.C000-01 Related Documents